How to properly sew jeans on the sides, waist, hips, legs, and back seam at home? How to sew on your own and reduce large men's and women's jeans to a smaller size? How to sew trousers - be your own tailor How to sew men's shorts for size M

Probably many people are familiar with the situation when you need to sew up your trousers and you seem to have a sewing machine, and your hands grow from the right place, but you don’t have enough skills? You can, of course, turn to the studio for help, but why then is this “Singer” or “Janome” standing in the room collecting dust? Of course, no one argues that it is more difficult to sew pants than a skirt or dress, but it is quite possible, the main thing is to follow our recommendations.

How to properly sew pants?

This is only at first glance, it seems that it is easy to sew in the sides and waist of the trousers. But there are a number of nuances here.

The main nuance is that you can sew up trousers no less than two sizes. Otherwise, you may warp the trouser legs and ruin the model.

If you see that you need to sew in more, then full cutting cannot be avoided. That is, rip apart at the seams, apply new patterns and make a pattern for them. Therefore, it is worth soberly assessing your strengths, and in order to avoid damage to the product, consider the option of handing over the trousers to the atelier.

The second nuance is that the trouser legs need to be sutured simultaneously along all seams: back, side and inside. Note! We will suture only on the outside if we need to remove excess tissue from the hips, and not the entire size. That is, when the product is your size, but does not fit well on the hips because there is not enough volume.

• Before picking up scissors and a needle, you first need to turn the product inside out and put it on yourself.
• Mark with pins the places where the model sits imperfectly.
• Then baste by hand and try on the front side.
• If what you see satisfies you, you can sew a machine seam.

If the trousers are a little wide, there is no need to rush and rather start stitching the side seam.

1. First, try on your pants;
2. Pin the outer seam and move around a little, squat down.
3. If you feel that they are “pulling”, most likely the inner stitching needs to be redone.

But in any case, before you take up the machine, first try on the trousers and determine exactly where you need to remove the excess. This is exactly the case when they say “ Measure seven times, cut once».

How to sew wide trousers in the waist and sides?

There are several ways in which you can sew pants in a belt, choose one of them:

• Sew only the side folds;
• Sew by making undercuts;
• Remove excess fabric by suturing the middle seam;

Below step by step description how to sew in trousers 1-2 sizes in the waistband, processing the middle seam:

1. First, open the belt loop, then the belt and cut it in half (at the back). Next, open the finishing stitch on the middle seam (on the butt). Then the seam itself is sutured;
2. Then the excess is removed from the belt. It is sewn together, the decorative stitching and belt loop are restored on the middle seam.

How to sew in trousers only on the sides?

• The product is also put on inside out and all excess fabric is measured in front of the mirror, on the hips, butt and legs;
• Then make temporary stitches on one leg and try on the product again, comparing both legs;
• If everything is basted correctly, then take off your pants again, place unnecessary stitches on them, then sew everything along the marked lines. In order to preserve the model, it is necessary to sew all seams equally - internal and external;
• Trying again. If everything is satisfactory, then the trousers are ironed, excess allowances are cut off and the edges are overcast.

How to properly sew women's flared trousers?

Sometimes the trousers fit perfectly at the top, but the cut at the bottom doesn't suit you.

And it’s not just about flares, which are now unfashionable, sometimes you want to narrow the usual straight model:

How to sew pants at the bottom?

• It will be easier to use a lifesaver in the form of tailor's adhesive tape. To do this, first determine the bend line.
• Then we cut off the excess fabric. You need to leave from 1 to 2.5 centimeters.
• Afterwards, the fold line is fixed with an iron.
• Next, a ribbon is inserted into it, you can insert it in parts and each part is ironed from the inside out.
• After the tape is fixed, make a circular stitch at the bottom of the pant leg, otherwise it may come off during washing.

There is also a method without tape.

1. Using it we again determine the length of the finished product.
2. Leave a seam allowance of 1 centimeter and cut off the excess.
3. We overlock or overcast the edge, and then on the wrong side we make a fixing stitch on the machine.

Rules for sewing trousers 1-2 sizes smaller

There are basic rules that should be followed when sewing in trouser legs. And it doesn’t matter whether you remove the size or the flare:

As you can see, there is nothing complicated in the question of how to sew in even wide trouser legs. The main thing is not to rush. Until the final stitch is done and the excess fabric is cut off, you will always have the opportunity to undo the threads and re-stitch. Happy sewing.

If you have a dress that is too big in size, then you can solve this problem at home. When mentioning a knitted product, we note that adjusting it to your figure will require less effort: the plastic fabric takes the desired shape quite easily. If the dress is wool, then it is advisable to subject it to wet-heat treatment (this causes shrinkage and makes the finished product smaller).

Preparing for work

It is recommended to place a knitted dress made of wool or wool mixture in a bowl of hot water and leave it there for a while. Then you need to wring out the item without twisting it and wrap it in a clean bath towel or sheet. Thus, excess moisture will quickly be absorbed into the towel.

Important! Drying on a line is contraindicated: in this case, the product will stretch and become deformed. It would be correct to lay out the undried clothes on a horizontal surface (for example, on oilcloth).

Is it possible to sew a dress to size?

The sleeveless model will be easy to fit to your figure with your own hands. To do this you need to do a fitting. Those places where the dress is too big for you need to be pinned with sewing pins (you need to remove all excess along the side seams, starting from the top - from the very armpits).

If you want the item to fit your figure, then you will have to work with the darts - smoothly deepen them in front and behind. The largest area of ​​fabric capture is at the waist line, from where the contour of each dart is drawn down and up (towards the bust line). It is better not to touch the central seam located on the back (especially if there is a collar).

Note: it will be easier to manipulate the volume of the product if you wear the dress inside out. In this case, all seams are accessible, and the adjustment process will not cause difficulties.

To work, you will need not only pins, but also a thin piece of soap (if the dress is dark). To draw lines on light fabric, a simple pencil is useful.

Besides, stock up on the following supplies:

1. measuring tape;
2. scissors;
3. needle and thread.

Where to sew a dress to fit?

So, if you decide to change your dress to a smaller size, then you need to sweep it along the lines that were marked with pins and then drawn with a soap or pencil. After this, you need to put the thing back on in front of the mirror. A second fitting is necessary to see how accurately the product fits your figure. Typically, the side seam moves 1.5-2 cm in the armpit area and is reduced to nothing at the very bottom.

Need to know! Seam allowances for thin fabrics are taken at 0.5 - 0.7 cm, and for dense ones - between 1 and 1.5 cm. The dress should not fit tightly to the figure, otherwise the seams will diverge and the fabric will gradually tear.

Based on the results of the final fitting, the product is washed off by hand, old seams are ripped out, and excess strips of material are cut off. Then you should make a stitch with a machine and remove the basting. If the material crumbles on the cuts, then you will have to process these places with a “zigzag”. New seams must be ironed.

At the last stage, the length of the product is determined (when cutting off the strips from the bottom, do not forget to leave allowances for the hem). If you didn’t know how to make a dress smaller, we recommend using the method described above.

It is advisable to take into account that under the dress you need to wear exactly the underwear with which you are going to wear it (only in this case the fit will be successful). If the cut of the clothing is not particularly complex, then it is quite possible to sew this model on your own.

How to make a large or wide dress smaller

1. in the shoulders
2. in the chest
3. at the waist
4. On the sides
5. in the sleeves

If you have sloping shoulders, you will have to change the slope of the shoulder line and slightly deepen the armhole at the side cut. In cases where it is necessary to increase the width of the shoulder section by 2 cm or more, then it is necessary to make changes to the pattern of the sleeve cap (and this already requires certain skills).

In order to shorten the length of the shoulder, you need to put on a dress and pin up the head of the sleeve at the level of the shoulder bone. The entire length of the sleeve is carefully pulled up and pinned to the future landing site. It is advisable to involve someone to help carry out this manipulation. The armhole will increase slightly from raising the sleeve, and you will need to reduce it under the armpit. After this, check to see if there is any excess volume left along the chest and waist lines. The armhole line should be strictly oval.

To alter a fluffy dress with a cut-off bodice yourself (for example, a wedding dress or a children's dress), you need to turn it inside out. You should lift up the underskirt lining to gain access to the seam where it is stitched to the mesh layers of the overskirt.

It is necessary to tear off sections of about 10 cm long from the corset of the dress (in the area of ​​the side seams). Through the ripped places, the product is turned inside out so that the entire side seam becomes accessible. Next, you need to draw a new line for the side seam with a simple pencil and make a line along it using a typewriter. The same manipulations are carried out with the lining.

The product is folded symmetrically in half, and the excess seam is cut off from the chest towards the back (along the neckline). The ripped areas along the neckline are sewn up, and the untouched lines are continued. We will have to take into account the original processing technology of a particular item. Some products have, for example, finishing stitching.

The folds of the upper skirt need to be collected and pinned together, adjusting to the desired volume. After this, the upper skirt is stitched to the corset part of the dress and the lower layers of the skirt are sewn on one at a time (the folds can be formed by hand). Lastly, the lining of the dress itself is sewn on. There is no need to iron the seams of the skirt here.

Attention! If the lining of the dress is not sewn on the bottom of the product, then getting to the wrong side and the necessary seams of the product will not be difficult for you. If the lining is stitched, then you will have to open a small opening in one seam in order to be able to turn the entire product inside out.

Note that for the second fitting you also have to prepare the neckline. To do this, the product must be pinned (folded in half with the wrong side inward, aligning the shoulder and side seams, neck, bottom and armhole cuts).

We also recommend watching a video on how to sew a knitted dress:

Let's take a look in your closet - how many jeans have accumulated there that for some reason you stopped wearing? You will probably be surprised that you can simply store so many jeans, and yet many of them are still in trend or made of very high quality material. Well, today we will try to correct this mistake and bring back to life at least those pairs that are slightly (or even much) too big for you on the sides or along the length of the trouser leg. Is it possible to sew jeans at home without ruining the product? Yes, yes and yes again! After reading our recommendations to the end, you will be convinced that sewing jeans with your own hands is very simple and any girl who does not have special dressmaking skills can handle this task.

Clothes that suit your figure: stylish and neat

Jeans are one of the favorite things of the entire beautiful (and not only) half of humanity, and all because they are practical, fashionable and perfectly emphasize the advantages of the silhouette. But at the same time, they have one drawback - all models are sewn, as they say, with the same brush, i.e. according to standard body shape standards. To correct this injustice, you just need to sew up your favorite jeans in some places. To do this you will need a little patience, determination and a sewing machine at hand.

Problem 1. How to sew jeans in at the waist?

In order to make jeans one size smaller at the waist, you need to prepare a tape measure, scissors, tailor's pins (sold at any sewing store), a sewing machine and thread to match the material. There are two ways to sew jeans in at the waist - simple and more complicated. We'll look at both.

The simplest thing is to adjust the trousers to your figure using darts. Step-by-step instruction next:

1. Put on jeans and visually mark the places where the darts will be less noticeable (as a rule, they are made on the back of the product in the buttocks area). You should also determine how many centimeters the jeans will need to be sewn in at the waist.

2. Now open a few centimeters in the waistband in the places where the future darts will be.

3. Baste the undercuts. Try on your jeans again. If there are enough decreases in the waistband, you can machine stitch the darts.

4. Now you need to sew in the belt. To do this, carefully cut extra centimeters material and carefully sew the sections with a machine stitch, having previously swept them by hand.

Advice! Do not make the darts in the waistband too long - this will cause the entire product to “bounce” upward in the buttock area.

The second way is to sew in jeans along the center back seam:

1. The first thing you need to do to fit the product is rip off the belt loops, which are located near the rear central seam. This also applies to the branded label, if it is also sewn very close.

2. Now you need undo the belt ten centimeters on either side of the center. The middle seam also needs to be split eight to ten centimeters down. Remove the remaining threads and secure the spacers. Do this carefully so you don't have to do a lot of corrections later.

3. Iron everything thoroughly.

4. Now turn the product inside out inside out and fold the legs so that the middle seam is facing you. Secure both halves of the jeans with tailor's pins to prevent movement.

5. The most crucial moment has come - you need to draw with chalk or soap line of the future middle seam. To avoid mistakes, draw it as follows: first, mark in the upper part (i.e., at the junction with the belt) a point at the distance you need (this distance is equal to half of your decrease). Now, with a smooth line, connect the point and the place of the bartack you made on the central seam. Try not to make the line angular.

6. Next step - sweep away the resulting dart and try on the jeans. If everything is in order, sew the dart on a sewing machine, trim off the excess fabric with an even allowance (0.7 - 1 cm) and overcast the edges with a zigzag stitch or overlock.

7. Now turn the product right side out and make two parallel lines, repeating the factory middle seam.

8. The next step is you need sew on a belt. To do this, attach it to the finished main product and cut off the extra centimeters. Be sure to take allowances into account.

9. Fold the waistband in half, right sides inward, machine stitch the seam and finish the edges. Now unfold the belt and iron it thoroughly.

10. Baste the belt back to the garment and try on the jeans. If you are happy with everything, you can stitch the basted seam and sew the belt loops/factory label back to their original place.

Problem 2. How to tape your trouser legs?

If your jeans are too big in your legs, you can sew them in discreetly along the inside seam. This is done like this:

1. Turn the jeans inside out and try them on. Mark the location of the future new seam using pins along the inside.

2. Carefully remove the item. Lay it out on a flat surface.

3. Now draw a dotted line in place of the pins. The pins should be left in place to prevent the fabric from shifting. Correct the line, continuing it to the very top along the inside of the product. If your jeans need to be sewn only along the leg, without affecting the seat depth, then the new line should start approximately three to five centimeters from the middle seam. If you need to sew in according to the planting depth, then, accordingly, the line should start from the central seam.

Advice! In order to properly sew a garment, it is better to use a pattern, but if you do not know how to make patterns, then try to ensure that your markings replicate the factory seam as much as possible.

4. Make a 1cm seam allowance near the new seam line.

5. Cut off excess material taking into account allowances. Fold the pant legs one on top of the other and transfer the markings.

6. Baste them first by hand, and then stitch them on a machine - this will make it easier for you to make a neat straight stitch.

7. Iron and finish the free edges.

Problem 3. How to remove flares?

Turn the jeans inside out and put them on. Use pins to mark the desired leg width. It is advisable to make decreases on both sides of the trouser leg.

• After removing the item, lay it out on a flat surface.
• In the places of the pins, draw a dotted line with chalk, continuing from the knee downwards. If the pins are not secured straight, adjust them, but do not remove them.
• Manually baste the legs taking into account the allowances and try them on.
• Now you can cut off the excess fabric and sew stitches and overcast stitches on the machine.
• Iron the stitches on the wrong side.
• Wear your updated jeans with pleasure!

So we looked at the most common ways to sew jeans at home. Don’t throw your favorite model far into the closet - now you can adjust it to your figure yourself, without resorting to the expensive services of a professional studio. Be bold - and your girlfriends will definitely envy your outfits!

It’s good when a person stays the same size throughout his adult life and can wear his favorite things for years. What if he gained weight or lost weight? And an expensive (literally or figuratively) shirt no longer fits your figure as well as before? Don't rush to get upset. It is possible that the atelier will help you adjust your clothes to your figure, and you will not have to part with your favorite things.

But here there are certain limitations. Igor Pronin's Fashion Salon will try to voice the main criteria that ateliers use when fitting clothes.

1. Suturing is always easier than increasing the size. Since store-bought items have a small seam allowance, you can arrange the clothes quite a bit. You can increase the size of jackets, coats, trousers (provided there is a certain margin in the seams). A shirt is almost impossible. The fact is that the collar on shirts cannot be altered. The only solution to the problem of a tight shirt collar is to rearrange the button on the rack.

2. If you want to sew your clothes, this will be much easier. But there are exceptions here too. You must understand that by suturing one part of the product, you will have to adjust the size of the rest, since the overall balance will be disrupted. As a result, the list of operations for adjusting clothes will be too large, and you will ask yourself a logical question: isn’t it easier to sew a ready-made shirt and not have to worry about alterations?

3. Things are different if the item as a whole is your size, but some of its parts do not fit well on the figure. For example, you just need to shorten the sleeves or hem the bottom of your trousers. Here the alteration is understandable and quite natural.

4. The most basic rule of the atelier is: each case is individual. Two people can come to a tailor with the same problem, the solution to which will be different in both cases.

Therefore, if something in your clothes does not suit you, but you like the thing itself and would like to wear it, feel free to take it to the atelier. A professional tailor will always advise the best way out of the current situation. And even if your favorite shirt is hopelessly small, you can always sew the same one, but in the right size.

We also suggest you look at the article with a new collection of fabric from the Royal Fabrics store. Corduroy in a variety of colors from Scabal will inspire you to create a new suit and bring bright colors into your life.

“We choose an atelier. Main selection criteria Difficulties are the engine of progress »

igorpronin.ru

How to reduce the size of something:: JustLady.ru

The same applies to items made from natural fabrics. Wash the item in hot water and rinse immediately in ice water. Then squeeze it at high speed and hang it on the radiator to dry.

The item can be sewn 1-2 sizes wide. Skirts, trousers, blouses, shirts are sewn in proportionally at the side seams. Put the item on inside out, fasten it, and use pins to pin up excess material at all seams. Then take off the item, baste along the pins with a contrasting thread, try it on again, if you like it, sew on the machine according to the basting. Cut off excess material with scissors, leaving 0.7 cm for finishing the edges. When sewing on a machine, pay attention to the coincidence of the side seams and the presence of decorative trim. The side seams of the waistband and hips must match and be positioned exactly in place, otherwise the product will not fit. Making sleeves smaller is more difficult. They must first be flogged, then the armholes must be sewn in, the sleeves must be sewn in, and then put back in place. You can also reduce the size of a blouse or dress by removing excess material in the darts. It is not recommended to sew up items larger than 2 sizes, because... in this case, you will have to rip the entire thing apart and sew it again to size. In principle, it’s easier to just sew a new one.

It is almost impossible to reduce your shoe size. You can only make it more comfortable to wear. To do this, fill the socks of your shoes with thick cotton wool. Or buy thick insoles for your shoes. Special stickers will help make large sandals comfortable for small feet. Glue them under your heels and they can hold your feet in the correct position.

But, of course, the easiest way is to buy things in your size. Then you won't have to figure out a way to do less. An item of the wrong size can always be exchanged in the store within 14 days for a more suitable one.

www.justlady.ru

fit of clothes to the figure price sew clothes increase decrease the size at the side seams jacket coat

Many representatives of the fairer sex take care of their figure. And in pursuit of beautiful external data, they throw off, most succeed, but at the same time they have to think about how to change their wardrobe. After all, your favorite ones become big, and you want to wear them all the time. In this case, if you have certain skills and a sewing machine, you can sew your outfit yourself.

To begin with, you should immediately note that you can reduce your trousers yourself. maximum only two sizes; if a larger size is required, then you will have to rip and reshape the product. In this case, beginners do not need to overestimate their strength and it is best to take the trousers to be altered in a studio, otherwise there is a risk that if sewn incorrectly, the outfit may become “skewed”.

What do you need to know?

To ensure that the product does not lose its original appearance, it must be sutured simultaneously from the side and from the internal (step) seam.

Suturing on one side only is possible only if when you need to remove some material from the sides.

As soon as it becomes noticeable that the legs have lost weight and only the hips need to be “cut off,” then you can sew the trousers only from the inside seam.

How to properly sew pants?

• first you need to find out where exactly you need to sew in your trousers (at the waist, on the hips or at the bottom);
• we rip the bottom backing, do it carefully with a special tool - a ripper; if you don’t have one, then ordinary nail scissors or a blade will do;
• turn the trousers inside out and put them on yourself. Then we make markings with pieces of old soap or insert pins in the right places;
• draw a straight line (or a tapering line) from the top point to the bottom, do the same with the second leg, manually stitch along the lines along the inside seam;
• we turn the pants inside out and try them on, you can walk around the room and also do squats. If the new one does not hinder movement, then cut off the excess fabric with a margin of 1 centimeter from the edge;
• we pass the sewing machine along the line;
• some jeans are decorated with a decorative seam, in this case we select the color of the thread and the length of the stitching so that there is no difference from the old seams;
• the edges need to be overlocked, and if such a tool is not available, then you can sew the edges with a zigzag or use a special attachment called an “overlock foot”;
• After this, be sure to iron the new seam so that no traces of the old cut remain. When doing wet-heat treatment, in order to avoid leaving traces of hems on the front side, you need to place strips of whatman paper along the edges.

Sewing the top of the trousers

When it comes to the waist, you also need to make sure that there are no constrictions. You can try removing the excess from the side seams and sewing it into the middle seam. Either pull them into darts, or, as an option, add separate darts.

It often happens that the waist and hip circumferences do not coincide with standard sizes. In this case, trousers that fit perfectly on the hips may be somewhat wide at the waist.

When the difference is insignificant, you can correct it with small darts or place it in separate pintucks.

In order for the trousers to look perfect after fitting, you need to do the following operations:

• turn the trousers inside out;
• rip the bottom part of the belt from the wrong side (this is necessary so that after re-stitching there are no traces left on the belt after suturing);
• sew in the waistband and side seams;
• add darts on the front and back sides of the trousers;
• put on the product and, if there is discomfort, make adjustments and re-sew the seams;
• steam all seams on an ironing board;
• carefully sew the belt back;
• After finishing sewing, re-iron the trousers using cotton fabric.

These tips apply to classic fabrics. Materials such as slippery silk, thin silk, bologna fabrics, as well as thick and unruly fabrics differ in tailoring and therefore it is better not for a beginner to start making such products. Once you have the skill, you can move on to more complex products.